Inevitably, we might experience challenging times, and during these phenomena, it may be harder to survive or communicate. And that’s the time we run to primitive instincts and resources, and one of those is a walkie-talkie where you use morse codes for easier and faster communication.
These morse codes are used to allow people to send and receive messages over telegraph lines. With just a few clicks, bleeps, or even light signals, you can already send help to you right away. In this article, we will tackle how to send morse code with a walkie-talkie device.
Short Answer
The right way to send morse code with a walkie-talkie is through the telegraph. All you have to do is keep its microphone close to your mouth to be heard clearly by the receiver. Then, you may need to hold the playback to the walkie-talkie’s microphone and utter the code words to relay the critical messages instantly. However, if verbal communication is not applicable, you may use the button’s dits and dots to transmit uninterrupted carrier wave transmission for SOS communication.
Long Answer
The morse code is undoubtedly the best option of communicating during emergencies that you may or will experience. It reads the absence or presence of a carrier wave signal and tuned frequency. However, you have to take note that morse code receivers are not designed to respond to the side bands (SSB or AM), which means it doesn’t affect any modulated sound.
The carrier wave is much stronger than its side bands, which means the signal is vivid at a significantly greater range than the walkie talkie voice. You may prefer to use commercially available equipment to transmit and receive because they sent the morse as rf modulated sound waves, then turned back into sound just as line voice could have.
Importantly, you need to realize that strict radio communication disciplines and procedures must be adhered to at all times when using a walkie-talkie. There are many reasons how important morse codes are in using a walkie-talkie device. First, you have to observe strict radio procedures to maintain the security and confidentiality of the information being transmitted.
Always remember that regardless of how secure the device you are using may be, it still operates based on the fact that someone could be listening in on your transmissions through frequencies and such. Thus, names of locations and operations involved should be disguised via morse codes or call signs.
How Morse Code Receiver Units work
So, how does a morse code receiver unit work? Well, receiving the signal is a bit tricky, especially when you are new in using a walkie-talkie device. First, you have to know the aspect of receiving one. You have to understand that if the signal was received in an ordinary domestic radio, you might hear some plops and clicks depending on the power signal. Second, to create a morse tone, the radio receiver must be equipped with BFO or the beat frequency oscillator or the CIO, carrier insertion oscillator.
To produce a specific morse tone, the radio receiver must have a beat frequency oscillator and carrier insertion oscillator.
Send Morse Codes with a Walkie Talkie
In sending morse codes, messages can be sent quickly using several abbreviations to ham radio and other radio communications operators. The usual amount of words that can be sent in a minute is 20 to use Morse codes effectively.
Morse code is a language that uses a series of dashes and dots to represent the different numbers, letters, and procedural notations. In sending these series of representations to the walkie-talkie, all you need to do is to turn the signal on and off in the right manner.
During the telegraph days, we could send a message using a single wire to create radio communication. This could be done by turning the transmitted signal on and off.
Morse Code Alphabet
Morse could usually be used right now within ham radio or radio communication for identifying directional beacons for aviation. Using the morse code may be a bit harder for some to decipher, especially for new users. However, once you get familiarized with it, morse codes can provide a powerful means of communication between different people. You need to introduce and get accustomed with abbreviations and codes.
The use of the codes forces a much more concise form of communication apart from allowing fewer letters to be sent. The other advantage of using these codes is that they enable ham radio operators who may not speak English (the most widely spoken language on the air) to communicate with a much wider number of people. Using the codes, it is possible to communicate with other ham radio stations quite easily with minimal English knowledge.
This communication method may not seem to be the latest in technology, but it still has many advantages in today’s fast-paced technology world. One of the most significant benefits of learning morse code through walkie-talkie is that you can use this in times of low signals, which may happen during emergencies. For instance, when you want to ask for help (SOS), you may need to send three points, one dash, and three points more.
Morse code is an informal language yet allows users to transmit information through simple clicks, light signals, or tones, that all can be conveyed with a dash and point. It is also essential to take note that Morse code can’t work with Cyrillic or other alphabets but based on the Latin alphabet and Arabic numerals.
Here are there defined lengths for the different elements within the Morse characters:
Dot = 1 dot length
Space between elements of character = 1 dot length
Dash = 3 dot lengths
Space between Morse characters = three-dot lengths
Space between words = seven dot lengths
Learn Morse Code
After familiarizing yourself with Morse code, it is vital to practice communicating in that language to retain the information and get comfortable using it.
The first step you must do is connect with another user to chat with on walkie talkie talk. At this stage, this person is the “BASE.” It would help if you gave a nickname to all the people you will be communicating with to point out the receiver of the message quickly.
All you have to do now is to say “to BASE.” After the recipient hears his designated nickname, he will respond by saying, “Go ahead.” Once the conversation is made, the caller may say “Clear.” The recipient needs to react by saying clear to end it smoothly.
Here are ways of learning the Morse Code:
Book
You may go to the respective library and find a Morse Codebook to help you decipher codes. Sometimes books are the best and easiest way to learn for you to avoid any distractions.
Online Resources
With our advanced technology these days, some may also prefer online courses and resources that capture your interest and makes the training more productive. This is also advantageous for some who don’t want to go out of their home’s comfort.
App
Another learning tool will be an App. All you need to do is to download the app on your smartphone/ tablet. These applications can teach you Morse code.
Always remember that in learning morse codes, patience and persistence are highly needed, for it takes a lot of time and determination.
Conclosure – How to send Morse Code with a Walkie Talkie
The Morse code through a Walkie-Talkie is still widely used for many instances and emergencies that might happen. All you need is equip yourself with the knowledge of using informal language and radio or ham radio applications. This enables ham radio contacts activated in any part of the world with ease. And quite the run to survival tool, especially when using low powers or more modest antennas.
